ServicesCode Corrections
Code Corrections and Inspection Fixes in Kennedale
When a home inspection or a permit inspection turns up electrical items, a closing or a finished project can sit waiting. We read each line, confirm what is actually wrong and correct it cleanly, with one person keeping you informed from the first call to the reinspection.
Turning an inspection list into finished work
Code corrections usually start with a piece of paper: a correction notice from a city inspector, or a home inspection report written for a buyer or seller. The notes are often brief, like "double tap at panel" or "no GFCI at exterior receptacle," and they rarely say how to fix the problem or how serious it is.
We go through the list item by item at your home, test what was flagged, and tell you plainly which items are genuine safety concerns, which are code requirements for the work being inspected, and which are recommendations you can weigh on your own schedule. Then we correct the items you approve, using proper parts rather than quick patches that a second inspector will catch.
The same person you speak with first stays on the job through the work and any reinspection, so nothing gets lost between the estimate and the final sign-off.
What the correction work covers
- 01
Panel and breaker items
Double-tapped breakers, oversized breakers on small wire, missing knockout fillers and incomplete circuit labeling are among the most common report notes. When the panel is sound, we correct them right there. When the panel itself is worn or unsafe, we show you what we see and walk through whether panel upgrades make more sense.
- 02
GFCI and AFCI protection
We add ground-fault protection where it is required, such as kitchens, baths, garages and outdoor receptacles, and arc-fault protection where the work calls for it. We check that the breakers or devices are compatible with your panel before anything is ordered.
- 03
Grounding and bonding
Three-prong outlets with no ground, missing bonding on gas or water piping, and loose grounding electrode connections all get traced and corrected rather than covered up.
- 04
Open boxes and exposed splices
Splices hanging in the attic, junction boxes without covers and cable left unprotected get proper boxes, clamps and covers so every connection is enclosed and accessible.
- 05
Outdoor and weather exposure
Exterior receptacles get in-use covers rated for wet locations, and damaged conduit or weathered fittings near the meter or air conditioner are replaced so the finish holds up outside.
Questions about Code Corrections?
Call(682) 357-4925When this service is the right call
A red tag or correction notice
Your permit inspection did not pass and the inspector left a list. We correct the listed items and coordinate the reinspection.
Electrical notes on a sale report
A buyer's or seller's inspection flagged electrical items and the closing date is set. We can review the report, give you a written scope, and help you decide what to correct before closing.
Work done by a previous owner
You have found wiring that does not look professional, such as cords run through walls, splices without boxes or an outlet added in an odd spot. We check it and bring it up to a safe standard.
An insurance or lender requirement
Some policies and loans ask for specific electrical items to be corrected. We do the work and explain what was done so you can pass it along.
How a correction job runs
- 1
Talk it through by phone
Read us the key lines from the report or notice and tell us the date you are working toward. We book the service visit around that deadline, whether it is a closing or a project wrap-up.
- 2
Review and verify at your home
We go through every flagged item with a tester in hand, take photos of what we find, and note anything the report missed that affects safety.
- 3
Written scope before work begins
You get a line-by-line list of what we recommend correcting and the price for each item, so you can choose what to do now and what can wait.
- 4
Corrections done with care
We protect floors and finished surfaces, make the repairs with materials matched to your system, and leave covers, plates and panel labels neat. Where the local jurisdiction calls for a permit, we pull it as part of the job.
- 5
Reinspection and cleanup
Where a reinspection is required, we arrange it and are your contact for the result. The work area is cleaned before we leave.
What moves the price of code corrections
Correction work is priced item by item, which keeps the total easy to follow. Most of the variation comes from how many items there are and how hard each one is to reach. We give you the written scope before any work starts.
- Number and type of items
- Swapping a receptacle for a GFCI is quick work. Adding a ground wire to an ungrounded circuit or rerouting a run is far more involved.
- Access to the wiring
- Items in an open garage are simpler than those in a finished wall or a tight attic. Attic work during a North Texas summer is also scheduled for cooler hours, which can affect timing.
- Panel condition
- Some breaker corrections need parts that are hard to source for older or discontinued panels. When replacement is the sounder choice, we explain why before you decide.
- Permit and reinspection
- When the correction requires a permit or a return visit from the inspector, that time and any fees are listed on your estimate.
Code correction questions
Do you pull permits and handle the reinspection?
Yes, when the work calls for it. We pull the permit wherever the local jurisdiction requires one and set up the reinspection directly with the inspector. You are not left passing messages between us and the city.
Can you fix only the electrical items on my home sale report?
Yes. We review the report, verify each electrical item, and give you a written list with pricing for each one. Some report notes are recommendations rather than requirements for an existing home, and we will tell you which is which so you can decide with your agent.
How long does a correction visit take?
A short list of outlet, cover and labeling items is often finished in a single visit. Items that involve rewiring a circuit, replacing a panel or waiting for a reinspection take longer, and we give you a realistic timeline with the written scope.
What happens if a fix uncovers a bigger problem?
We stop and show you what we found, with photos, before doing anything beyond the agreed scope. You get an explanation and a revised price, and nothing changes without your approval.
Who do I talk to while the work is underway?
The same person who reviewed your report. They answer your questions, schedule the work and the reinspection, and confirm when everything is closed out.
Get your inspection list closed out
Have your report or correction notice nearby and we can talk through it on the phone. From there we set a visit to verify each item and give you a written scope.